Proprietary Material & Process Shop Broadheads
Engineered Confidence

Engineering Report

Proprietary Material & Process

Real engineering data. Purpose-built broadhead performance.

At Annihilator, we believe performance claims should be supported by real engineering data.

While we do not disclose the exact alloy, manufacturing parameters, or heat-treatment specifications used in our products, we do believe hunters deserve transparency regarding the performance of the materials behind them.

See the data
01

Why Broadheads Are Different

Our broadheads are manufactured using a proprietary material and process specification developed to maximize structural strength, impact resistance, dimensional consistency, and edge stability. Unlike many broadheads that focus heavily on steel names, we focus on the complete system that determines real-world performance. Many premium steels are marketed using the same language commonly found in the knife industry.

Knife steels are often optimized around wear resistance, corrosion resistance, and long-term edge retention.

However, broadheads face a different challenge.

Unlike a knife, a broadhead must withstand impact, compression, bending, and torsional forces simultaneously.

Our material and process specification was selected with these real-world conditions in mind.

A broadhead is not simply a cutting edge. It is an impact-driven cutting structure.
02

What Is Yield Strength

Yield strength is the point where a material begins to permanently deform.

For a broadhead, this matters because hard impact can create substantial bending and torsional forces.

Higher yield strength helps a broadhead maintain its intended geometry when those forces occur.

Yield strength answers a simple question: how much force can the material take before it starts to permanently bend?
03

Engineering Performance

  • Yield Strength ~276ksi ~1900 MPa
  • Hardness ~54HRC Rockwell C

Our proprietary material and process specification produces a rare combination of high structural strength and broadhead-appropriate hardness.

These values place our material among the highest-strength materials used in the broadhead industry.

Why Hunters Care

  • Resists Bending

    Helps maintain intended geometry during impact.

  • Protects Edge Geometry

    Hardness helps preserve cutting performance.

  • Maintains Structural Integrity

    High strength helps the broadhead continue functioning under extreme loading.

  • Consistent Manufacturing

    Produced to tight dimensional standards.

04

Different Materials. Different Objectives.

Not all steels are designed for the same purpose.

  • Some prioritize wear resistance.
  • Some prioritize corrosion resistance.
  • Some prioritize shock resistance.
  • Some prioritize structural strength.

Material selection always involves tradeoffs.

Our goal is not to optimize for a steel name. Our goal is to optimize for broadhead performance.

Typical hardness and yield strength by material
Material Hardness Yield Strength Optimized For
A2 Tool Steel 58–60 HRC 150–170 ksi Wear resistance and tool stability
S30V Stainless 58–61 HRC 180–220 ksi Wear resistance and corrosion resistance
S7 Tool Steel 54–56 HRC 200–235 ksi Shock resistance and toughness
Annihilator Proprietary Material & Process ~54 HRC ~276 ksi Structural strength and impact resistance

Higher HRC is not better here. Past roughly 58 HRC a steel trades toughness for wear resistance. A broadhead that chips is worse than one that dulls.

Published values vary based on heat treatment, manufacturing method, geometry, and final application. Values shown represent typical industry ranges and our proprietary material/process specification.

Yield Strength Typical low Typical high
  1. A2 Tool Steel 150–170 ksi
  2. S30V Stainless 180–220 ksi
  3. S7 Tool Steel 200–235 ksi
  4. Annihilator ~276 ksi
05

Why We Don't Publish The Alloy

We believe customers deserve transparency regarding performance.

We do not believe competitors need a roadmap to replicate the work behind our products.

For that reason, we publish the engineering performance data that matters most while keeping the specific alloy, manufacturing parameters, and process specifications proprietary.

The result is meaningful transparency without disclosing the intellectual property behind our products.

06

More Than Just Steel

Material selection is only one part of the equation.

Final broadhead performance is influenced by the complete system.

  • 01 Material Selection
  • 02 Manufacturing Process
  • 03 Geometry
  • 04 Heat Treatment
  • 05 Finishing Operations
  • 06 Quality Control

This is why we focus on engineering the entire system rather than marketing a single material name.

07

Built for Performance

Every design decision we make is driven by a simple objective:

Build the most effective and reliable hunting broadheads possible.

The material and manufacturing technologies behind Annihilator products are part of that commitment.

Performance first. Results that speak for themselves.